Guest

  • Following 0 users
  • Followed by 0 users
  • Votes 0
  • Subscriptions 18

Activity overview

Latest activity by Guest

  • Guest created a post,

    CTRL PWM control brightness on a TFT scree

    1. Community
    2. TFTs

    I am trying to control the screen brightness with a PWM signal on a NHD-7.0-HDMI-HR-RSXP-CTU.The PWM signal is generated by an arduino, by setting its hardware registers (as described here:https://...

    • Guest
    • 5 followers
    • 12 comments
    • 0 votes

  • Guest created a post,

    CTRL PWM control brightness (NHD-7.0-HDMI-HR-RSXP-CTU)

    1. Community
    2. TFTs

    What should be the voltage of the PWM signal that controls brightness on the NHD-7.0-HDMI-HR-RSXP-CTU display?

    • Guest
    • 2 followers
    • 2 comments
    • 0 votes

  • Guest created a post,

    How work with NHD-0216AW-SB3

    1. Community
    2. OLEDs

    Good afternoon! I want to use the NHD-0216AW-SB3 display in my design, but having looked at the instruction set I do not understand how to form them. For example, D / C #, R / W # signals for displ...

    • Guest
    • 1 follower
    • 1 comment
    • 0 votes

  • Guest created a post,

    TFT LCD drive problem

    1. Community
    2. TFTs

    Hi,ı am trying to drive the TFT LCD modüle (it's link is below) , and i am not sure that the initial parameter values for LCD are the right values. when i init the LCD i can not see anything on the...

    • Guest
    • 1 follower
    • 1 comment
    • 0 votes

  • Guest commented,

    1. Community
    2. TFTs
    3. Connecting 18bit controler to 24bit display

    Is the connection schematic that you attached suitable for NHD-3.5 320240MF ATX tft module ? I will connect the R0,R1,G0,G1,B0,B1 to the GND and R2-R7 to MCU R2-R7 (  B2-B7 to MCU B2-B7 and G2-G7 t...

  • Guest commented,

    1. Community
    2. TFTs
    3. NHD-7.0-800480EF-ATXV

    We don't have any documents that pertain to the correlation between porch settings and ghosting/flickering.  This is something you will notice as the porch settings are adjusted for the display.  T...

  • Guest commented,

    1. Community
    2. TFTs
    3. NHD-7.0-800480EF-ATXV

    You will have to determine the values that you need for your setup.  Even if you use a value from that range, the display may show ghosting and/or flickering if not optimized properly.

  • Guest commented,

    1. Community
    2. TFTs
    3. NHD-7.0-800480EF-ATXV

    By default the source driver is set to DE mode.  There is no pin on the 40 pin connector that allows you to change this mode.Please refer to page 6 of the specification sheet for the horizontal and...

  • Guest commented,

    1. Community
    2. TFTs
    3. Soldering and mechanical attachment

    In that case you can use plastic standoffs for those two holes to secure the FPC when you install your display

  • Guest commented,

    1. Community
    2. TFTs
    3. Soldering and mechanical attachment

    The holes on the FPC are used for aligning the board when soldering.  They should not be used to mount the display.  On the back of the display itself there are two strips of double-sided tape.  Pe...