NHD-C0216CiZ-FSW-FBW-3V3 not working
Hi,
I'm trying to get the NHD-C0216CiZ i2c display to work with an Arduino leonardo, but can't get any results. the wiring is as follow
RST: pulled high to 3.3V with 4.7K resistor
VDD to 3.3V
VSS to GND
Vout connected to VDD through a 1uF cer cap
C- an C+ connected together through a 1uF cer cap
SDA and SDL connected to the 5V i2c bus through a level shifting circuit as describe by application note AN10441 fron nxp semiconductor :
http://www.nxp.com/documents/application_note/AN10441.pdf
I tested the i2c bus and level shift circuit by connected other i2c device both on the 3.3v and 5V sides and they work correctly( mcp9600 tested on 5V side and DAC6573 tested on 3V side)
The display backlight is turn on, but I don't see any other sign of activity on it. I tried to reset it by pulling RST low and it doesn't change anything
The display doesn't acknowledge the i2c adress. Tried both (0x7C and 0x3E). I can clearly see the master sending the b0111 1100 adress byte but the sda lines then stays high with no aknowledge.
I tried varying the SCL speed down to 15kHz and 8kHZ with no results.
I also tried ignoring the NACK and sending the rest of the initialisation routine. I used the code posted on your forum here:
That does'nt work.
I noticed that the sda and scl lines get pulled down from 3.3V to 2.1V when I connect the display. I don't no why it does that.
Does someone have an idea of what could be the problem?
-
Hello,
I have another example code for this display here:
I was able to get this to work with an Arduino Mega with a 3.3V regulator.
The Voltage should not be dropping to 2.1V when you plug in the display.
Has this only occurred with one unit or multiple units?
Can you also confirm that you are going right to left for the pin numbers?/*****************************************************/
/*
C0216CiZ.c
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
*/
/*****************************************************/
/*****************************************************/
unsigned char text1[]={"NEWHAVEN Display"};
unsigned char text2[]={"2x16 LCD Module "};
unsigned char text3[]={0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08,0x09,0x0a,0x0b,0x0c,0x0d,0x0e,0x0f};
unsigned char text4[]={0x10,0x11,0x12,0x13,0x14,0x15,0x16,0x17,0x18,0x19,0x1a,0x1b,0x1c,0x1d,0x1e,0x1f};
/*****************************************************/
#define SDO 22 //Serial data
#define SCLK 23 //Serial clock
#define RESET 24 //RESETET
/*****************************************************/
const char Slave = 0x7C;
const char Comsend = 0x00;
const char Datasend = 0x40;
const char Line2 = 0xC0;
/*****************************************************/
/*****************************************************/
void I2C_out(unsigned char j) //I2C Output
{
int n;
unsigned char d;
d=j;
for(n=0;n<8;n++){
if((d&0x80)==0x80)
digitalWrite(SDO, HIGH);
else
digitalWrite(SDO, LOW);
d=(d<<1);
digitalWrite(SCLK, LOW);
digitalWrite(SCLK, HIGH);
digitalWrite(SCLK, LOW);
}
digitalWrite(SCLK, HIGH);
while(SDO==HIGH){
digitalWrite(SCLK, LOW);
digitalWrite(SCLK, HIGH);
}
digitalWrite(SCLK, LOW);
}
/*****************************************************/
void I2C_Start()
{
digitalWrite(SCLK, HIGH);
digitalWrite(SDO, HIGH);
digitalWrite(SDO, LOW);
digitalWrite(SCLK, LOW);
}
/*****************************************************/
void I2C_Stop()
{
digitalWrite(SDO, LOW);
digitalWrite(SCLK, LOW);
digitalWrite(SCLK, HIGH);
digitalWrite(SCLK, HIGH);
}
/*****************************************************/
void Show(unsigned char *text)
{
int n, d;
d=0x00;
I2C_Start();
I2C_out(Slave);
I2C_out(Datasend);
for(n=0;n<16;n++){
I2C_out(*text);
++text;
}
I2C_Stop();
}
/*****************************************************/
void nextline(void)
{
I2C_Start();
I2C_out(Slave);
I2C_out(Comsend);
I2C_out(Line2);
I2C_Stop();
}
void CGRAM (void)
{
I2C_Start();
I2C_out(Slave);
I2C_out(Comsend);
I2C_out(0x38); //go to instructino table 0
I2C_out(0x40); //Set CGRAM addRESETs to 0x00
I2C_Stop();
delay(10);
I2C_Start();
I2C_out(Slave);
I2C_out(Datasend);
I2C_out(0x00); //write to first CGRAM addRESETs
I2C_out(0x1E);
I2C_out(0x18);
I2C_out(0x14);
I2C_out(0x12);
I2C_out(0x01);
I2C_out(0x00);
I2C_out(0x00); //8 bytes per character
I2C_out(0x00);
//continue writing to remaining CGRAM if desired
I2C_Stop();
}
/****************************************************
* Initialization For ST7032i *
*****************************************************/
void init_LCD()
{
I2C_Start();
I2C_out(Slave);
I2C_out(Comsend);
I2C_out(0x38);
delay(10);
I2C_out(0x39);
delay(10);
I2C_out(0x14);
I2C_out(0x78);
I2C_out(0x5D);
I2C_out(0x6D);
I2C_out(0x0C);
I2C_out(0x01);
I2C_out(0x06);
delay(10);
I2C_Stop();
//CGRAM(); //define CGRAM
I2C_Start();
I2C_out(Slave);
I2C_out(Comsend);
I2C_out(0x39);
I2C_out(0x01); //go back Home
I2C_Stop();
delay(10);
}
/*****************************************************/
/*****************************************************/
void setup() {
pinMode(RESET, OUTPUT);
pinMode(SDO, OUTPUT);
pinMode(SCLK, OUTPUT);
digitalWrite(RESET, LOW);
delay(10);
digitalWrite(RESET, HIGH);
delay(100);
}
void loop() {
init_LCD();
delay(2);
Show(text1);
nextline();
Show(text2);
delay(2500);
while(1){
digitalWrite(SDO, HIGH);
delay(1000);
}
}0
Please sign in to leave a comment.
Comments
1 comment