NHD-1.8-128160EF-CTXI#

ljit

• June 25, 2015 09:07

Hello, I am attempting to wire the above LCD to an MCU that only has SPI and I2C. Apparently, the ILI9163 controller can be used with SPI. Is anything other than 8-bit parallel supported on the NHD-1.8-128160EF-CTXI#? Thank you very much for your help.

0

• 

  Paul_B

  • June 26, 2015 09:07

  Hello,
  
  NHD-1.8-128160EF-CTXI# only supports a 8‐bit Parallel interface.
  
  Have a great weekend!

  0
• 

  zramaro

  • July 22, 2015 09:07

  Hello,
  
  I'm planning to use the NHD-1.8-128160EF-CTXI# on my project.
  It's wrtitten in the datasheet to solder directly the LCD connector to the PCB. I'm wondering if it's the only option or if there is a socket I can use to connect the LCD connector.
  
  Thanks in advance.

  0
• 

  Paul_B

  • July 22, 2015 10:07

  Hello!
  
  The LCD connector on NHD-1.8-128160EF-CTXI# needs to be soldered directly to the pcb (via a Hot-bar machine).
  
  If you are interested in a traditional FFC ZIF LCD connector I recommend using the following display:
  
  NHD-1.8-128160EF-CTXI#-F

  https://newhavendisplay.com/1-8-inch-standard-tft-without-touchscreen/
  
  LCD Connector: 24pin 0.5mm FFC connector. Molex P/N: 52435-2471

  0
• 

  zramaro

  • July 22, 2015 11:07

  Hello Paul,
  
  Tnanks for the answer.
  
  I'm planning to use the NHD-1.8-128160EF-CTXI#-T because the Touch Panel is available on this device which is not the case with the NHD-1.8-128160EF-CTXI#-F. Please correct me if I'm wrong.
  Can you please tell me if this is a device of similar size with ZIF connector and Touch Panel controller.
  
  Regards,
  Zafi.

  0
• 

  enjaian

  • July 23, 2015 12:14

  Hello Paul,
  
  I'm also looking at a variety of New Haven LCDs for a project. I read that you stated that if a datasheet states the connector should be hot-bar soldered it cannot be used with a FFC ZIF connector. Is this because of an electrical issue or there just aren't surface mount connectors for it? Thanks for your help.
  
  Best,
  Jesse Enjaian

  0
• 

  Paul_B

  • July 23, 2015 13:07

  Morning Zafi,
  
  I recommend using NHD-1.8-128160EF-CTXI#-FT:
  
  https://newhavendisplay.com/1-8-inch-standard-resistive-tft-display/
  
  Please note this particular display is Non-Stocked and requires a MOQ of 3000 pc.
  
  
  The MOQ maybe an issue in your case, it might be worth taking a look at our 2.4" Resistive Touch TFT's with a standard FFC ZIF connector (In-Stock):
  
  https://newhavendisplay.com/2-4-inch-standard-resistive-tft-display/
  
  Hope this helps!

  0
• 

  Paul_B

  • July 23, 2015 15:07

  Hi Jesse!
  
  Great question, when a display has a Hot-bar connector the flex needs to be soldered directly to the pcb. You will not be able to locate any standard FFC connectors to accommodate this.
  
  There are a lot of benefits for using a direct flex-to-board connection. It saves vertical height, can be more reliable than fine pitch connectors and saves the cost of the connectors.

  0
• 

  zramaro

  • July 23, 2015 16:07

  Hi Paul,
  
  Thank you for the answer and suggestion. The MOQ is a bit high for my need. Using a NHD-2.4-240320CF-CTXI#-FT could be the best option.
  
  Regards,
  Zafi.

  0

Please sign in to leave a comment.